How to configure production labels for a label printer

How to configure production labels for a label printer

Summary

This article explains how to configure the Solatech Window Covering Software to use production labels on a label printer.

More Information

In order to use a label printer with the Solatech Window Covering Software (SWCS) you will need to perform the following steps:

  • Create and configure a custom printer configuration specific to the label printer
  • Modify the labels to use the new printer configuration
  • Modify the layout of labels

Create and configure a custom printer configuration specific to the label printer

In order for SWCS to print labels on a label printer it needs to know some specific information about the size of the labels, the margins, etc. In SWCS, this information is stored in a Printer Configuration.

To create a printer configuration

  1. From the File menu, click Printer Configurations.
  2. Select the printer configuration (Production Labels-AV5162).
  3. From the toolbar, click the Copy button.
  4. Enter a name for the new configuration, for example "Labels on Label Printer", and click OK.

To edit the configuration for a label printer

  1. From the File menu, click Printer Configurations.
  2. Select the printer configuration you want to use for production labels. If you followed the steps above, select "Labels on Label Printer."
  3. Assign a printer to the configuration if it does not have one already.
  4. From the toolbar, click the Page Setup button.
  5. On the first tab, Margins, enter the margins for the label printer. Refer to article "How to determine the margins of your printer" for information on how to find the margins.
  6. On the Paper tab, enter the physical size of one label.
  7. On the Label Layout tab, enter the width and height of the label after the margins. For example, if the paper size was 4 x 2 and the left/right margins were .1 then the width would be 3.9 (4 - .1) and the height would be 1.9.
  8. Leave the horizontal and vertical gaps at 0.
  9. Change the columns per sheet to 1 and the printing direction to Across and Down.
  10. Click OK.

Note: The preview window may indicate the settings are invalid. In this case the warning can be ignored.

Modify the labels to use the new printer configuration

Once the printer has been setup the labels needs to be modified to use the new printer configuration.

  1. From the Tasks menu, click Manage Process Reports.
  2. Select the Production Labels category.
  3. Select the first label and click the Modify button on the toolbar.
  4. On the Layout tab, check the box "Use a custom printer configuration for this report".
  5. From the list of printer configurations, select the one you created for your label printer.
  6. Click OK.
  7. Repeat steps 3 - 6 for each of the labels you'll be printing in the label printer.
  8. Close Reports Center.

Modify the layout of the labels

After setting up the printer configurations and assigning them to the labels the last step is to

review/change the labels to make sure they are designed to fit the label printer.

  1. From the Tasks menu, click Manage Process Reports.
  2. Select the Production Labels category.
  3. Select the first label and click the Modify button on the toolbar.
  4. On the Layout tab, click the Change Label Layout button.
  5. Review the fields to make sure they all fit within the gray box. The gray box defines the size of the label and anything that is outside the gray box won't print.
  6. Make any required changes and click OK.
  7. Click OK again to save the changes.
  8. Repeat steps 3 - 7 for each of the labels you'll be printing on the label printer.
  9. Close Reports Center.

REFERENCES

For more information, refer to the following knowledge base articles:

  • How to determine the margins of your printer

APPLIES TO

  • Solatech Window Covering Software 4.2

    • Related Articles

    • How to setup SWCS to print dot-matrix production labels

      Summary This article will explain how to setup the Solatech Window Covering Software to print production labels on a dot-matrix printer. More Information In order to use a dot-matrix label printer with the Solatech Window Covering Software (SWCS) you ...
    • How to create, modify and setup production labels

      This article explains how to create, add and modify custom production labels.  Solatech provides default labels in the software; however, they cannot be customized.  Below are the steps for creating a new label that can be modified to fit specific ...
    • Production labels 'creep' when printing from print preview

      Symptoms When production labels are printed from within the Print Preview dialog, the labels 'creep' up or down. By 'creep' we mean that each label starts printing a little bit up or down relative to the previous or next labels, instead of in a fixed ...
    • How to put images on production labels

      Summary This article explains how to put images on production labels printed with the Solatech Window Covering Software. More Information Putting labels on production labels is a two-step process. The first is to find the image and update your ...
    • How to sort production labels by an option value

      Summary This article explains how to setup production labels to sort by an option value. More Information The default sorting for production labels is first by order number, then line number. If you want to sort by any other field you must create a ...